DIY Tub Installation.
DIY Tub Installation.
Blog Article
We have encountered this great article relating to Installing A Bathtub down the page on the web and decided it made good sense to discuss it with you on this site.
Setting up a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard project. If the old bathtub is conveniently available, the job can move quickly; if you have to open up a wall surface to remove the old bathtub as well as place the new tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and set in the brand-new one. Make sure you have actually certified yourself for the job and also are comfortable trying it. Rather than hiring a service provider to take control of a halfway-completed task, it is better to take into consideration employing one before you start. Possibilities are you might require a specialist plumber to make tube connections.
This article will help you set up a new tub in your washroom if you have actually currently acquired a brand-new tub and don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also product list need to make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washers are in area between the faucet and the sink. Safeguard the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for setting. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as readjusting the feet on the bathtub up until the level checks out level.
To mount taps, fit the bottom of the furthest versatile faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Switch on the supply of water and also inspect all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill up the bathtub and likewise check the overflow outlet and also the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait till the bathtub has actually been made use of at least once as this will certainly resolve it into its final setting.
Preparing for the Installment
Firstly, the sustaining framework supplied with the bathroom should be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, bring about issues with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components as well as installations. They are sold in tubes as well as cartridges, and also can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the floor tiles using waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog post on A Step-by-Step Guide to Installing a Bathtub when doing a search on the internet. You should take a moment to promote this write-up if you enjoyed reading it. Kudos for your time. Visit us again soon.
Request Service Report this page